loading
SINOCONVE conveyor belt manufacturer & supplier makes conveyor belt more efficient.

Copper Mine Conveyor Systems: From Pit Edge to Concentrator

Copper Mine Conveyor Systems: From Pit Edge to Concentrator

A line on the pit plan ends at the concentrator. In the equipment list it has somehow become four conveyors. The pit wall might demand one break. The road crossing might demand another. But a short link between two contractors’ drawing sheets deserves a harder look. Put a pencil dot wherever ore falls and ask the designer why the upstream belt stops there. That question comes before cover grade.

The sketch starts at the crusher and ends at the concentrator feed. Show the trucks only where they hand ore to a crusher or belt. After processing, use a new sheet for concentrate load-out. Its fine material, enclosure and cleaning duty cannot be described by the same note that covers the coarse feed from the pit.

Send the pit-to-plant route drawing for a transfer review

01Put a number on every drop

On a print of the flowsheet, circle every discharge in pencil. Do the crusher and the mobile unit each have one? Is there a short link belt before the fixed incline? Does the last flight empty into a bin, and how is that bin reclaimed? The circle follows the falling ore, even when the chute belongs to a different contract. That contract boundary is precisely where dimensions can be missed.

Each pencil circle gets a notebook entry. At one, take a sample of the biggest common ore piece; at the next, photograph the entire stream in motion. Put a tape between the current liner lip and the receiving belt. The drawing’s structural elevations may be correct while the new liner leaves less room than the chute designer expected. Make a separate wet-season note for the place that bridges after rain.

A blocked-chute probe may be drawn above a chute that a fitter cannot reach. Look for the platform, the liner withdrawal path and the place where an isolated blockage can be removed. A dust hood needs room too. At each circle, ask where fine material lands when the stream is disturbed. If the answer is the walkway, the transfer is not finished merely because the belts align on the drawing.

Red circle on the route Site measurement Drawing that should answer it
Crusher to first conveyor Largest recurring lump and actual fall Chute and receiving-belt support
In-pit to fixed flight Position after each planned shift Move sequence, take-up and transfer interface
Two overland flights Trajectory at minimum and maximum feed Chute, liner access and dust containment
Plant feed bin Buffer capacity and outlet behaviour Bin level, feeder and shutdown sequence

Save the marked route as revision zero of the transfer list. Later drawing changes can then be checked against a count rather than a vague promise to “minimise transfers.” The mining and quarrying page gives the wider application context; this list is for one route.

02Where trucks stop carrying the repeat haul

The trucks are still needed for changing faces and waste. The repeated loaded run from a crusher toward the plant is the possible conveyor job. Measure that journey for the current pit and for the later benches on the mine plan. A face that is close to the rim today can be a much longer and higher haul later. That change belongs in the comparison with fuel, tyres, road maintenance and shift delay.

One arrangement worth drawing places the crusher close to the face and shifts it as mining advances. A movable belt follows, then hands ore to a fixed flight. The truck journey gets shorter; the conveyor now has to be moved in planned windows. On the second-stage pit plan, draw the new tail and cable position. Does the moving discharge still meet the fixed receiving chute without an awkward drop or extra link belt?

The crossover between trucks and conveying has no universal distance printed on it. Plot the site’s production rate and remaining years, then put the electrical supply and move costs beside the fleet costs. A buffer bin can let the crusher and long flight stop at different times, within its useful capacity. Show the outlet feeder and the bin’s maximum and minimum operating levels. A square labelled “surge” on a flowsheet cannot absorb an unlimited outage.

Steel cord belt section prepared for a copper mine conveyor splice

On a long mainline, the belt construction follows the calculated tension, pulley and splice duty. The companion article on steel cord belts for copper mines deals with the material’s effect on the belt itself. A route study first needs to decide where that belt begins and ends.

03The transfer drawing nobody wants to own

At a boundary between two equipment packages, the upstream team draws a discharge envelope; the downstream team draws a loading zone. Put both on the same sheet. The ore stream needs a trajectory through the intervening space. There should be enough room for a replaceable liner, a cleaner where needed, a skirt enclosure that can be serviced and a place for material to go during a blockage.

At a truck tip, take the measurement with the tray in its dumping position. At a crusher discharge, take it with the current liner fitted. The nominal elevations may be accurate and still miss the lump’s landing path. Video helps here: at low rate, a stream can hug one wall; at full rate, it may reach the middle of the receiving belt. Keep both clips with the chute revision.

Trace the air as well as the ore through the transfer. A skirt box that is too short releases dusty air; a belt sagging beneath that box opens the seal. The cleaner’s discharge should return removed fines to the intended material path. Increasing skirt pressure against a poorly supported belt is a quick way to put a long stripe in the cover. The impact support note addresses the belt beneath the stream.

Cutaway idler roller showing bearing and seal construction

We make the conveyor belts. Idlers and related hardware can be supplied through qualified partners. Put the service position on each component request: a dusty crusher feed, exposed overland return or damp plant transfer will not age rollers in the same way. A sealed bearing does little to stop paste building on the outside of its shell. The roller range provides options once those positions are known.

04One flight, or a break at the pit rim?

Try the unbroken route on paper first. Calculate belt tensions in steady operation and during the starts, stops and loaded restart that the controls must manage. Add the take-up, pulley sizes, drive position and splice class. Then put the calculation on the actual terrain profile. A flight that fits the belt catalogue can still conflict with a road crossing, a curve or a maintenance route.

Now draw a break at the pit rim and calculate again. The incline and overland run become separate drives and separate tension systems. That may lower the demand on one long belt, but it buys a tower, new loading zone, instrumentation and maintenance access. Put both options on one cost sheet, including the lost production when either chute blocks. The answer is site-specific; “fewer transfers” alone does not settle it.

Route choice What the design gains What must be recalculated
One continuous flight One less discharge and receiving chute Peak tension, take-up, pulley and field splice
Break after steep climb Incline can be designed as its own drive section Transfer impact, dust, power and access
Shiftable in-pit segment Crusher follows mine development Move schedule, cable route and changing interface
Buffer before plant Pit and plant can stop independently for a while Bin capacity, reclaim feed and blockage control

Write the reason beside each proposed break. “Reduces calculated peak tension beyond the available belt build” is reviewable. “End of package A” is an administrative boundary, not an engineering reason. The result may still require a transfer, but at least the team can see what it purchased.

05The climb and its two curves

A pit exit has more than a gradient number. At the foot, the belt enters a vertical curve; at the crest, it leaves one. For both, check the belt’s contact with the idlers and the distribution of tension across its width under loaded and unloaded conditions. A curve radius that looks generous on the civil drawing may not suit the chosen belt or its tension range. The conveyor designer should set the radius from the belt and load calculations.

For the ore itself, test the steepest section with representative material. Size distribution and moisture affect rollback, especially during starting and stopping. There is no single safe copper-ore angle to paste into every design. A change in chute feed can leave the belt more heavily loaded at the bottom of the incline than expected. Watch a controlled loaded start during acceptance, then check the tail for rollback and spillage.

At the crest, note whether the carrying belt stays on its intended support and whether material spreads sideways. Changing the grade of rubber does not correct a poor vertical curve. Nor should an idler be forced against the belt as an improvised hold-down. Recheck radius, tension and support geometry with the conveyor designer before altering hardware.

A horizontal bend around a bench adds another set of checks: side force, belt tracking, idler banking where designed, load position and available clearance. A training idler is a maintenance aid, not a licence to draw a tighter curve. If the feasible curve radius cannot fit the bench, that is a real reason to compare a new flight and transfer with earthworks or a different route.

06Power and access belong on the route plan

Trace the proposed line with a maintenance vehicle, at least on the drawing. Where does it cross to the other side? Which pulley can be reached by lifting equipment? Can a crew get a replacement idler to the middle of the run after rain? At a transfer tower, the cleaner and blocked-chute sensor need reachable working positions. A note that says “maintenance access by others” is not a route.

A drive station needs more than a motor symbol. On the electrical sheet, show supply, start, braking, backstop where needed, trips and local isolation. The load case to worry about may be a full incline after an unplanned stop, not a steady hour at design tonnage. Ask the controls team to write the start and stop sequence in plain words. Feed should not continue into a belt that has tripped downstream.

For the movable section, draw the cable and substation in both the present and next position. A fixed flight needs a road that remains usable when an idler fails in bad weather. On the plan, choose a realistic place to set down a replacement pulley, then trace its path to the drive. Check who has the lifting gear and whether a vehicle can reach the pad. A pulley in stores is only useful when that journey works.

Steel cord spools used in belt production

The route finishes at a plant feed bin carrying crushed ore. Label that hand-off clearly. If a later diagram includes filtered concentrate going to the yard or port, start a new material description at the process boundary. The port bulk handling discussion fits that later part of the chain.

07The drawing package to send for a quotation

Send the plan and elevation with each transfer numbered. Add capacity range, speed, ore size distribution, moisture condition, planned mine stages and the intended moves of any in-pit equipment. Mark the steepest loaded section, horizontal and vertical curves, roads, power locations and available maintenance access. Include the drive and tension calculation if it exists. Without that information, a belt quotation prices a roll, not a route.

Ask the conveyor designer to state the alternatives considered for each major break. The belt manufacturer can then discuss carcass, covers, splice and delivery against a defined duty. Components such as pulleys, troughing idlers and cleaners can be coordinated with qualified supply partners. Keep the same drawing revision on every related RFQ.

The material-facing construction is a separate decision. Read the companion copper-ore belt article once transfer heights and the long-flight tension are known. For other minerals, the lithium, copper and rare-earth comparison covers broader material differences. Neither replaces the route drawing.

Request a review of your transfer list and belt duty

08Questions from the route review

How many pencil circles survive the review?

Look at the dots on the marked plan. Ask which one would force an impossible tension, crossing or curve if removed. Put that explanation beside the dot. For any dot left over only because two contractors drew separate sheets, have them produce a joined route option and price it. The count is an outcome of that exercise, not a standard number.

Can a long flight replace truck haulage?

It can replace a repeat haul between defined points. Trucks may still serve moving faces and waste. Compare the route over several mine stages, including crusher moves, capacity, power, maintenance and the effect of a single stoppage.

What changes when one circle disappears?

The remaining flight grows longer. Put its new tension, take-up travel, drive, pulley and splice calculations beside the removed tower and chute costs. Draw access along the extra length. If that flight cannot follow the terrain or be installed and maintained, the pencil circle returns to the drawing.

Does a steep pit exit require a special cover?

First test whether the actual ore stays on the belt through a loaded start and stop. Separately calculate belt tension and check the curves. Cover grip is one part of the problem; geometry, feed and drive control also matter.

Why is the crest spilling?

Look at belt support, curve radius, load shape and tension at the crest. Confirm the belt remains where the design expects under load. A cover-grade change is unlikely to correct an unsuitable curve.

What should be on the first site walk?

The numbered transfer list, current route drawing, ore sample, intended mine stages and an access sketch. Walk the future drive and chute locations with maintenance, electrical and process staff before the civil layout is fixed.

prev
Steel Cord Conveyor Belts for Copper Mines: What the Ore Actually Does to the Belt
Conveyor Belts for Motor Vehicle Plants: Body, Paint and Final Line Duties
next
recommended for you
Get in touch with us
QUICK LINKS
CONTACT US
Contacts: Leo Lei
Tel: 0086-18668582073
Address: Room 1602, sanlong building, tiangao street, south cbd, yinzhou district, ningbo, zhejiang ,china


We are focusing on material handling, power transmission and industry application.

Copyright © 2026 Ningbo Sinoconve Belt Co., Ltd. - www.scconveyorbelt.com | Sitemap | Privacy Policy
Contact us
email
whatsapp
Contact customer service
Contact us
email
whatsapp
cancel
Customer service