At the conveyor, the belt edge has been touching a guard near the tail. The removed guide has one polished flank. Mark both contact points on the replacement drawing; the belt and frame tell the same story from opposite sides.
A profile chart can identify the guide family. The worn surface tells the crew whether the old installation had room to run, which is the more urgent question before another belt is made.
Send your belt and groove drawings for a fit check
Watch the machine through a few empty circuits. Put a temporary reference mark on the frame at each end and write down the edge gap. Now feed the usual cartons, including the side transfer.
The job is to locate the force that has been pressing the existing guide against one wall.
A centre guide limits lateral movement within its groove. It has no way to make an out-of-parallel pulley stop pulling.
The same reasoning applies when choosing among PVC conveyor belts. Cover material and top-side grip answer different questions from underside guidance. A textured cover may hold a carton on an incline yet do nothing for belt tracking.
A buyer may write “K10” on the enquiry; the machine shop still needs a cross section. The maker of the actual guide should provide its height, widths at stated measurement points, flank angle and groove recommendation. Different extrusions sold under a familiar K designation need not have identical working dimensions. The worn guide is an identification clue, not a reliable master for cutting a fresh groove.
On a single-centre-guide conveyor, check that every pulley and contact roller needing a groove has one in the same lateral position. A guide touching the face of one un-grooved roller will lift the belt or rub itself away. Two guides can help when the machine has a wide belt and a defined need for symmetric restraint; they also demand more accurate parallelism between the two groove paths.
| What to measure | Why it matters | Warning on the removed belt |
|---|---|---|
| Guide section and supplier drawing | The groove must clear the guide root and tip while supporting the intended flank contact. | A flattened tip or continuous mark across the root. |
| Groove centreline at each pulley | A lateral offset makes the guide bend sideways between rollers. | One polished flank and a matching worn groove wall. |
| Groove depth and bottom clearance | Bottoming can carry the belt off the pulley face. | A polished guide tip, intermittent loss of belt contact or bouncing. |
| Flank clearance and finish | Pinching creates heat; excessive clearance permits repeated side impacts. | Melted PVC or, at the other extreme, battered flank edges. |
| Belt splice and guide transition | A proud splice or abrupt guide end can strike the groove entrance. | A peel starting at one guide end, often near the splice. |
A statement such as “K10 groove” leaves room for two workshops to cut different sections. Put the supplier’s cross section beside the pulley drawing, with the intended clearance and the measurement point marked on both.
A bottom-side guide may be welded to a compatible PVC cover.
Along a long run, inspect the interface and the fabric immediately beside it.
Show the splice, direction of travel and both guide ends on one drawing. A raised joint strikes the groove repeatedly, particularly if the guide crosses that change in thickness. The allowable end treatment and spacing belong to the chosen belt construction and welding process. A dimension from a previous purchase order is useful history, not proof of fit on a different belt.
| Where the separation begins | Evidence to preserve | Question for the belt maker |
|---|---|---|
| At the entrance end of the guide | A lifted corner, impact mark or matching burr at the groove lip. Mark the running direction before removal. | Was the guide end shaped for this groove and does it encounter a proud splice? |
| Along much of the welded root | The exposed underside of the guide, any porous patches and the appearance of the cover below. | Which belt and guide compounds were joined, and what did the bond trial show? |
| Beside the splice | A local step in belt thickness and the location of the guide end relative to the finger or step joint. | Does the splice layout allow the proposed guide transition at that point? |
| At repeated bends | Root cracks at regular intervals, especially near a small return roller. | What minimum pulley diameter applies to the finished belt, guide and splice together? |
A replacement return roller sometimes arrives without a groove. Another may have a groove at the wrong offset. Either can scrape a correctly fitted guide in a single shift.
Shiny sides and PVC smear suggest flank pressure or pinching. A polished tip suggests bottom contact.
Observe the belt empty, then with the usual product and side infeed. A frame that twists under load may change the edge gap although the empty test was quiet.
Packaging conveyors often have one small roller that is easy to miss on a general arrangement drawing. The guide bends over it on every circuit. A deep, solid V may develop root cracks there, even if the larger drive pulley presents no problem. A notched version divides that bend into shorter pieces, though the interruptions also change how continuously its flank bears on the groove.
The pulley limit on a datasheet for plain PVC belting describes a different assembly. Ask the maker to confirm the belt with its splice and fitted guide over the smallest diameter on this particular route. Include the return side and any nose bar. A guide that clears the drive can still be forced through a tighter reverse bend elsewhere.
Cracks at every notch suggest repeated bending stress. Note which pulley the damaged section has just passed and compare that bend with the guide supplier’s limit for the complete assembly.
| Choice on the drawing | What it solves | Question before approval |
|---|---|---|
| Solid centre guide | Continuous contact with one groove and a simple single-path layout. | Does the smallest pulley allow the complete guide and splice to flex without lifting? |
| Notched centre guide | More flexibility through a tight bend while retaining a central path. | What notch spacing and side-load limit apply to this actual profile? |
| Twin guides | Two constrained paths on a wide belt with defined asymmetric loading. | Can both grooves be kept parallel and in registration across every pulley? |
| No guide | Avoids underside welding and groove machining on a machine that tracks reliably. | Has tracking been observed with normal product and changeover loading? |
| What the team sees | Likely place to investigate | First check |
|---|---|---|
| Only one guide flank is shiny | Sustained lateral force from tracking or an offset groove | Measure pulley alignment and groove centrelines with the belt installed. |
| Both flanks show impact marks | The belt is moving between groove walls | Check groove section, belt tension and variable side loading. |
| Guide tip is flattened | Insufficient groove depth or one un-grooved contact roller | Trace the guide path through every return roller. |
| Short cracks repeat at notch roots | Bending demand at a small pulley | Compare the complete assembly diameter limit with the smallest pulley. |
| The guide lifts from one end | An abrupt transition, splice step or localized bond fault | Mark the end orientation and inspect its first contact point. |
| Belt edge rubs while guide looks intact | Guide/groove offset or too much allowed travel | Measure edge clearance through a loaded circuit. |
On machines that frequently change product formats, compare tracking after each changeover. A new side feeder angle or a different carton mass can alter the load the guide carries. The guide is part of the system specification, alongside conveyor pulleys and the frame, rather than an accessory selected only by belt width.
A purchase order that says only “PVC belt, endless, K10 centre guide” leaves the hard part for the installer. Put the endless length, width, carcass, covers, splice and running direction on the same sketch as the guide centreline. Add the smallest pulley and the path of the return strand. A photo of the old flank wear beside that sketch tells the fabricator why the belt is being replaced.
The quotation should come back with a guide section and a companion groove drawing. It should also name the attachment method and the diameter limit for the finished assembly.
On the machine, note the belt edge gap during empty running and again under representative loading. Stop once more to look for fresh shine or heat at the guide.
The signed measurement sheet and the old-belt sample will be useful when the conveyor is revisited months later.
| Acceptance stage | Record on the job sheet | Reason to pause |
|---|---|---|
| Bench, before fitting | Belt width and length, guide centreline at several points, splice and end transitions. | Guide position varies around the loop or a transition already lifts. |
| Machine isolated | Actual groove section, depth, offsets, burrs and the smallest roller in the guide path. | A roller is ungrooved or its groove falls off the common centreline. |
| Empty run | Head and tail edge gaps, guide contact and unusual noise over multiple circuits. | Persistent pressure on one flank or a visible sideways walk. |
| Normal loading | Edge gaps with ordinary side infeed and after product changeover. | Loaded frame changes the path or the belt touches a guard. |
| Stopped inspection | Fresh polishing, PVC debris, temperature, splice condition and tip contact. | New wear appears before routine production has begun. |
Request a guide and groove drawing review
An empty run can reveal a frame or pulley error. The case for guidance is stronger when normal side loading moves an otherwise well-aligned belt.
Possibly, if the cover accepts the bond and the endless loop can be processed without damaging its splice. Check every roller along the proposed groove path.
Use the cross section for the particular extrusion being purchased. Its width at a named height, flank angle and depth belong on the pulley drawing.
Inspect the first point of groove contact and the splice step. A peel along the full root calls for a separate bond investigation.
It can bend more easily, but confirm the full assembly against the smallest pulley and the expected side load.
Look at guide flanks, tip and root, both belt edges, splice and all groove entrances. Record whether wear is on one side or both and recheck after any pulley replacement or product changeover.
Related Articles:
PRODUCTS

We are focusing on material handling, power transmission and industry application.