loading
SINOCONVE conveyor belt manufacturer & supplier makes conveyor belt more efficient.

Polyurethane Belts: Where PU Earns Its Price and Where It Fails

Polyurethane Belts: Where PU Earns Its Price and Where It Fails

Consider a replacement enquiry. The old belt is lying on the bench with its splice folded back. White on top, a grey line through the edge. On the quote it had been called a PU belt, which is true as far as the carrying face goes. The grey line matters more to this particular replacement: the pull sits in a fabric layer, and the nightly rinse reaches it at the open edge.

01Start with the failed piece

On my sketch the edge gets a circle in pencil. The smallest roller gets another, with its measured diameter in the margin. I put the old splice beside the drawing, still damp if it has only just been removed. A spare offcut, when there is one, goes in a separate dry bag. It gives the supplier a reference for the old colour and thickness; a worn belt on its own cannot.

The maintenance crew may also put a solid white belt on the bench. The cut face has no woven line. Good for an edge that gets wet; perhaps awkward for the roller already on the machine. We still have to measure it. Some homogeneous belts have embedded cords. They are another construction again, with tension and pulley requirements written for that design. I would keep all three photographs rather than calling them equivalent by colour.

Polyurethane conveyor belt sample showing its surface and construction

At the drive cabinet there may be a toothed PU belt. That one has its own record: pitch and profile copied from the pulley, width measured at the unfrayed section, cord construction taken from the maker. Its back marking helps identify length, subject to the catalogue convention. It does not answer whether the smooth product belt will wash clean. Mixing those two on one enquiry is how a supplier ends up pricing the wrong thing.

The first measurement on the smooth-belt sheet is the return diameter, including its sleeve. Next is the nose bar if it is fixed rather than turning. A belt rated for a small roller does not automatically run over a stationary knife edge. The joint has to bend there too. If the old seam has a lip on the underside, I record which way that lip meets the roller. That little detail can explain a noise that was blamed on the pulley bearing.

Habasit's T22/PU data sheet puts TPU on the conveying face and polyester in the traction layer. It is a useful example to attach to the enquiry because the two materials have separate jobs. No claim about “PU elongation” can be read from the cover name. I would ask for the section drawing, allowable pulley diameter and splice detail of the proposed replacement, then compare those with the machine notes.

The price comparison comes last. If the old cover is still sound while the edge or joint has opened, buying a dearer surface compound misses the failure. If the whole face is scored by product, a different surface may pay for itself. The failed strip tells us which bill to examine.

Ask us to compare the old belt with your machine drawing

02Put a Price Against the Actual Constraint

The machine arrived last year; nobody plans to move the transfer now. Its return roller measures 24 mm with the sleeve; the transfer has a fixed 8 mm nose. One quotation says “PU,” the other says “rubber.” Neither has answered the fitter's question yet. I want the allowed diameter for each proposed belt, including the joint. If one cannot make that bend, its lower price is irrelevant.

Line note Why a PU construction might earn its place What to check
Tight transfer A thin coated fabric may go around the little nose Published knife-edge and pulley limits, including any reverse bend
Fat on the carrying face A rated PU cover may retain its shape and clean up well Specific fat or oil, temperature, cleaner and contact time
Open food product A homogeneous belt may remove exposed fabric from the food zone Belt-specific compliance paper, edge, joint and wash method
Positioning drive Tooth engagement on a corded belt Copy the pulley profile and pitch onto a separate drive sheet

The rubber quote stays on the table. White rubber exists. So do rubber covers formulated for oil. A heavy product landing on the belt asks for load support and impact tolerance that a thin process belt may not have. I set the two quotes beside the failed sample, not beside each other. Where did the old belt actually give way? If the cover is intact but the edge has unravelled, there is little value in buying a more expensive cover.

03The Bend is a Machine Dimension

On the sketch I mark three circles: head, tail and the little snub hidden under the return. The snub often decides the bend. The installed tail has a sleeve, so its diameter is measured outside the sleeve. A stationary nose bar gets a fourth mark. The supplier's sheet needs to cover that return, not only the head pulley.

The old belt has a shiny track on its underside, 18 mm in from the left edge. With the machine stopped, the track lines up with a raised fastener on the slider bed. There is the first repair. A new thin belt will pick up the same line. The cover compound did not create that screw head.

I leave a box on the drawing for “joint over smallest roller.” If the old splice has a lip, its travel direction goes there too. A joint may be the stiffest part of a flexible belt, and the click heard on each rotation can be the joint striking the roller. The maker should rate the fitted loop, not merely the unjoined material.

The operator also wants to know whether a lighter belt cuts motor load on the indexing conveyor. I would take a running-current reading with the present product first. Pretension and slider friction can consume more of the motor's effort than the change in belt mass saves. That question belongs in the trial log; it is not a promise on the PU quote.

The V-belt and timing belt from the same machine go back into the drive cabinet until their own measurements are ready. Groove and wrap for the first; tooth form, pitch and cord for the second. The small roller on the product conveyor tells us nothing about either drive.

04Oil on the Cover, White at the Edge

At the filling end there is a light grease line under the chain. At the slicer there is fat on the product face every hour. I would not put both belts on an order marked simply “oil resistant.” One exposure reaches the return side by accident; the other is part of normal production. The cleaner and its rinse may spend more time on the belt than the oil does.

On the sample tag I write “chain oil below,” then the cleaner's name and the time it stays on the belt. The cover feels softer at one edge, but the tail pulley is dirty on that side as well. The fitter's tracking marks run toward the same edge. I would clean the pulley and check tension before attributing every millimetre of drift to oil uptake. The stain tells us where the liquid landed; it has not diagnosed the cause of mistracking. A rated PU cover may hold its dimensions well in fat; a suitable oil-resistant rubber cover may do the same. The shop can compare two marked offcuts after exposure, with the same liquid and rinse.

For the white sample I turn the cut edge toward the light. A white product face over a grey fabric does not become a homogeneous white belt because the catalogue calls it food grade. I put the food-contact declaration for the exact belt beside the sample. Then I check whether exposed food touches that face, the splice, the guide or only a sealed carton. The answer changes which paperwork and cleaning details belong on the order.

A solid white belt keeps yarn out of that edge. It may call for different tension or a toothed drive. A coated fabric may make the tight transfer more easily. At the nose, look for dark yarn appearing through a worn face; at the seam, look for a pocket that holds rinse water. The audit is of the installed loop, not just the swatch in the sample book.

05Holes Need a Drawing

On the vacuum line, a carton has to cover enough holes to be held over the plenum. On the wet grading line, the water has to fall into a tray below the belt. Those are two reasons to buy perforation and two different hole drawings. I would mark the first and last active holes relative to the vacuum box or drain, then lay the smallest product over a paper copy of the pattern.

Duty Hole pattern on the drawing What to look for later
Vacuum hold-down Hole size and pitch over the plenum Poor grip outside the box; marks on the carton
Wet transfer Open area above a catch tray Blocked holes and water on the return
Crumb removal Passage for the actual crumb size Debris packed into the support plate
Point loading Sound material between holes Tears bridging adjacent holes

The remaining strips of belt between holes carry the pull. Open-area percentage does not give the whole strength reduction, because a row of holes across the width cuts a different path from staggered holes. If the belt has fabric, the punch can expose yarn. I would ask for the working rating and a sample edge after perforation, and keep holes out of the splice zone agreed with the fabricator.

There is a modular option when the whole conveyor can be redesigned. Its open links may drain well, but the hinge pins need cleaning and the drive needs sprockets. I would put the frame sketch and wash access beside that quote. On an existing pulley machine, changing to modular is more than ordering another belt.

06Wet Duty: Find Out Which Layer Failed

A belt removed after washdown may have a chalky patch near the tail. I would not write “hydrolysis” on the failure sheet from that colour alone. Cleaner residue can leave a pale film; the roller can abrade a surface; a splice can lift while the face remains sound. The failed strip and an unused offcut should be kept apart and labelled. They give the maker something better than a photograph of a belt on the floor.

PU is a family, and wet service separates its grades. Some polyester-based formulations lose properties with prolonged hot-water exposure. Hydrolysis-resistant grades, including some polyether choices, are available. Then there is the fabric beneath the cover, and the adhesive or weld at the joint. A chemical rating for the face does not automatically rate that whole stack.

PU belt surface and edge for washdown inspection

The cleaning record belongs beside the belt drawing. I want the actual wash temperature at the nozzle, the cleaner name and dilution, how long it sits, and whether a rinse follows. A weekend shutdown is different from a short warm spray during production. The belt may rest in a pool on the return run for two days; the same face, elsewhere on the line, may be dry by morning. A blocked tray outlet can therefore be part of a “material failure.”

Observation Check before blaming the PU Follow-up
Tacky patch below the wash nozzle Cleaner mix, temperature and rinse, plus a clean offcut Ask the supplier to check the exact compound
Fabric showing at one edge Guide contact, tracking and edge seal Correct the rub and specify the edge
Joint lifted near the tail Pulley diameter and lift direction Review joint preparation and its bend rating
Crosswise cracks on the bend Age, cycle count and wash record Section the strip; review material and geometry

I put the seam and the sound belt into separate sample bags. If a peel begins under the splice, the joint procedure deserves its own review. If cracks repeat at every small pulley, the bending history goes on the lab note. If only the wet side has softened, the operator's cleaning log matters. The visible symptom points the investigation; it does not finish it.

Forbo lists hydrolysis-resistant urethane coatings on specific food belts. Habasit also lists homogeneous TPU belts and reinforced variants. I would request the data for the proposed part number, not borrow a claim from the family brochure. The question for the maker is whether the cover, traction layer, edge and joint together tolerate this plant's time-temperature-chemical cycle.

Sometimes a grade change is enough. Sometimes the edge needs sealing or the drain needs fixing before any replacement is fitted. A rubber belt with the right compound is another candidate if the load and geometry permit it. “Chemical resistant” on a catalogue page cannot stand in for the cleaner's name and concentration on the work order.

07Make the Replacement Quote Checkable

The purchasing request says “white PU, 600 mm wide.” I set it next to the failed loop and there are still blanks: overall length, fabric or solid build, underside, and a splice that must pass a small snub roller. The line is washed at night. Those blanks are why two suppliers can quote very different prices and both believe they answered the request.

RFQ line What I would attach Why it stays on the order
Belt identity Edge photograph, both faces, old part marking Establishes the layer and tension construction
Machine Head, tail, snub, knife edge and take-up drawing Checks bends and fitting access
Contact Product, load point, oil or fat, cleaner and heat Gives the maker the real duty
Surface Grip or release note; a swatch if available Avoids a smooth face on an incline
Features Hole layout, guide, edge seal, joint direction Keeps the fabricated loop measurable
Evidence Required food-contact declaration and tolerances Ties documents to the supplied part number

At the last line I add acceptance details: width and length tolerances, splice appearance, edge finish, and any test report requested by the plant. If holes are specified, the drawing marks their pitch and a clear zone at the seam. A hardness number can go there too, with its test method; it cannot replace the construction drawing. The person fitting the loop should see this sheet before the order is released. The maintenance fitter stops at that line and points to the closed frame. An endless loop will not pass through it without dismantling a shaft. That fact changes the joint discussion before anyone buys material.

Polyurethane belt sample ready for dimensional comparison

When the replacement arrives, its marking goes beside the approved sketch. The start-up card carries the fitting tension and the first tracking observation. The bed screw that scored the old belt has a separate repair entry. We can close that entry before putting another loop over it.

Send your belt drawing for a replacement quote

08Frequently Asked Questions

Why does the “PU” sample show grey yarn?

The PU is its white working face; the grey is a textile layer below. I put this sample beside the solid white one and mark them as different builds on the order. A layer sketch clears up the rest.

The old belt turns around a tiny snub. Will this one?

The smallest pulley and any reverse bend need measuring. A fixed knife edge is recorded separately. I send those four dimensions with a photograph of the old joint. The answer needs to cover the finished loop.

How much strength does perforation remove?

There is no useful single percentage to subtract. Hole spacing, alignment, fabric and the remaining strip between holes matter. The working rating should be for the fabricated pattern, with the seam position shown on the drawing.

Is a white PU belt automatically food grade?

No. I ask for the declaration covering the exact belt and the relevant market. On the line sketch I circle the actual contact: open food, sealed carton or return roller. The edge and joint need inspection under the plant's cleaning plan.

Does washdown rule out PU?

No. A rated wet-duty grade may work. The maker needs the cleaner, dilution, temperature, contact time and idle condition. I would check the joint and fabric edge as carefully as the cover after a trial.

When is rubber the better buy?

A rough loading point, sharp point loads or a long heavy run can put the case in rubber's favour. For oil and cleaners, compare specific compounds. The failed belt and the machine geometry decide more than either family name.

prev
V-Belt Selection by Failure Mode, Not by Catalogue Section
Conveyor Belts for Cement Plants: Five Stages, Five Different Duties
next
recommended for you
Get in touch with us
QUICK LINKS
CONTACT US
Contacts: Leo Lei
Tel: 0086-18668582073
Address: Room 1602, sanlong building, tiangao street, south cbd, yinzhou district, ningbo, zhejiang ,china


We are focusing on material handling, power transmission and industry application.

Copyright © 2026 Ningbo Sinoconve Belt Co., Ltd. - www.scconveyorbelt.com | Sitemap | Privacy Policy
Contact us
email
whatsapp
Contact customer service
Contact us
email
whatsapp
cancel
Customer service