loading
SINOCONVE conveyor belt manufacturer & supplier makes conveyor belt more efficient.

Thicker Cover or Better Compound: What Actually Sets Abrasion Life

Thicker Cover or Better Compound: What Actually Sets Abrasion Life

The first number I look for on a worn belt is usually not the nominal cover thickness. I want to know where the fabric first showed. Under the chute? Along the right-hand skirt? At a joint that thumps over the tail pulley? Those three answers can lead to three quite different purchases, even if the last purchase order said “abrasion resistant” in all three cases.

Take a familiar argument from the purchasing meeting. One quote offers a thicker top cover. The other names a different compound, with the old dimensions left alone. If the cover has worn down in a fairly broad, shallow patch, I would be interested in the compound data. If it has been punched through in three places below an unsupported chute, I would walk the loading point first. There is no formula that converts one millimetre of rubber into a certain number of months. The piece of belt on the workshop floor has already supplied the more valuable evidence.

The following comparison starts with that used belt. Keep the belt orientation marked when it comes off the frame; a chalk arrow for travel and a mark for the drive-side edge will do. You can then match a scar to the chute lip, scraper or skirt instead of trying to reconstruct the layout from memory a week later.

Send photos of the worn belt and its loading point for a cover review

01 Read the Damage Before Buying More Rubber

I would lay the removed belt out with its travel direction still visible. On the first piece, the hollow might start where sand slows under a skirt; on another, the deepest hole sits directly below a liner with its bottom edge turned outward. Same word on the purchase order, quite different trouble on the conveyor. For a groove at the edge, run a finger along the skirt rubber and look underneath for embedded grit. Then turn the belt over. A loaded return roller can make a mark whose source was never on the carry side.

One close photograph of the hole is not enough. Take another from above, with the chute and both edges in view, and put a rule in the frame. I also mark whether I am looking at a single injured length of belt or a stripe running all the way round it. That distinction can save a long argument over rubber grades. Isolate the machine before reaching any guard or underside of the frame.

An unworn shoulder makes a handy comparison, though it need not equal the delivery-sheet figure. On a torn cover, the gauge tip can sit on a loose lip while the ply beneath is nearly bare. I prefer a cut cross-section from the scrap belt when the last millimetre matters. Label it “under chute,” “shoulder,” or “skirt side”; bare numbers on a maintenance sheet lose their meaning fast.

The first field sort

What you find Likely cause Where to inspect Belt or site response
Broad, smooth loss where fines slide Sustained rubbing and material settling Skirt length, burden motion and cleaner contact Cover compound and measured top-cover allowance
Scattered cuts and torn lips below the chute Lump impact, sharp edges or both Drop path, lump size, rock box and support Impact or cut-resistant construction and support geometry
Narrow straight groove beside a skirt Concentrated rubbing or a captured particle Skirt setting, trapped material and edge support Repair the contact; then assess remaining cover
The same bruise at each splice pass Joint impact or trapped buildup Joint profile and pulley wrap Check the splice, clean the pulley and inspect lagging

A sketch with the damage marked on it is worth sending along with the enquiry. There is a rubber conveyor belt catalogue and a page for abrasion-resistant conveyor belts. I would send the sketch with either enquiry. Otherwise the response may be a catalogue choice made without seeing the stone chips packed behind this particular skirt.

02 Sliding Wear: Compound Changes the Rate

Sand looks harmless coming off a chute until you lift the skirt after a shift. The grains next to the rubber have barely moved; above them the burden has travelled on. A smooth hollow beneath that skirt is the sort of wear for which I would request compound samples and their test sheets. I would also take a jar of the feed. Dry round sand, wet packed fines and freshly crushed sharp grains do not make quite the same contact, however similar their belts look from the walkway.

Here the test sheet becomes useful, provided the two figures share a method. ISO 4649:2024 uses an abrasive sheet on a rotating drum and reports volume loss or an abrasion index. A number without method A or B, or without any test identification, tells the buyer very little. The ISO text even warns against translating its result directly into service life. On a transfer with mostly sliding fines, I would use the figures to compare samples and then follow the installed belt’s wear trend.

Suppose the old belt has lost cover evenly along the first stretch after loading, with no local exposure of fabric. A compound change can lower the rate of that loss while keeping the familiar belt geometry. Extra cover also extends the distance to the carcass, but it leaves the rubbing mechanism in place. Whether that extra reserve is worthwhile depends on the actual wear trend, cost and the conveyor’s allowable mass and bending characteristics.

Look for a second influence before blaming the compound. A scraper pressed too hard can polish a neat strip into an otherwise healthy cover. A skirt that holds a bed of wet fines can turn a modest sliding duty into abrasive paste. Correcting either condition makes the next belt comparison meaningful. Without that correction, two different compounds are being tested against a fault in the machine.

03 Lump Impact: Cover Depth Is Only One Part of the Landing

Large, angular pieces do not politely rub away the surface. They strike, rotate and sometimes catch an edge as the belt accelerates them. Torn flaps around the loading point tell you to examine the landing path. Measure the free fall below the last chute surface, then find the point that takes the largest pieces. If a rock box has worn through or the landing is between two supports, that deserves attention before the cover drawing. Operators may remember an oversize piece hitting a different part of the belt during a surge; an empty-chute photo cannot settle that question.

More top cover can give a sharp lump more rubber to penetrate before reaching fabric. It can also protect a sound construction against occasional local loss. It does not correct a long unsupported span or an exposed steel edge. On sharp scrap I would ask to see a sample of the impact and cut-resistant belt, including its cut edge. Where is the breaker? How does the crew carry it through a splice? Those two details are easier to judge with a sample in hand than from the name of the range.

The carcass enters this discussion when the belt dives between supports beneath a heavy lump. A heavier fabric might reduce that movement, but it can give the installer a new headache at the tail and along the trough. I would ask for a drawing of the present idler spacing and the pulley list before changing plies. Check the proposed belt against every installed drive, tail and bend pulley before accepting a heavier build. ISO 3684 provides a method for minimum pulley diameter; the belt maker’s construction-specific recommendation is also needed.

Check the transfer in order

Start at the chute lip. A projecting wear liner can cut a cover while appearing to be ordinary impact damage from a distance. Then look for material packed between the belt and support. Check the first idler set after loading for an abrupt change in trough angle. On the scrap belt, a bruise underneath the torn patch is worth circling with chalk. Put that marked piece beside the transfer drawing when discussing the replacement. You may end up buying a belt and repairing a liner, but at least the two costs have named causes.

Item on the quote Possible benefit at this loading point Detail to verify
Add top-cover thickness Reserve against local penetration and wear Belt mass, flexing, splice design and pulley guidance
Change the cover compound Cutting or rubbing response, depending on formulation Evidence for the actual wear mode and chemical exposure
Change carcass or add breaker Resistance to deformation or propagation of cuts Troughing, tension, minimum pulleys and splice procedure
Improve loading support or chute The contact that damages each successive belt Accessible maintenance, material buildup and belt clearance

04 A Groove Near One Edge Is a Machine Clue

An edge groove can consume a new belt quickly while the middle remains almost untouched. The tempting purchase is a thicker cover. The useful first job is to find what stays in contact with that narrow strip. A skirt lip may have collapsed. A return roller may carry a hard ridge of buildup. An offset chute may load one side until the belt presses into a guide. A trapped fragment can travel at the skirt line and deepen the score.

Follow the mark along the conveyor. Does it begin at the loading point, at a cleaner or farther down the return? Is its width the same as the rubbing component? Are its walls polished, torn or freshly cut? These small details matter more than a generic claim that “the edge wore out.” Once yarn shows through, the question is no longer just cover life. Water can enter the fabric, and the supplier should see the damage before deciding whether a local repair is sensible.

If a replacement is already on order, record the alignment, skirt clearance and condition of return rollers before installing it. Otherwise the plant may spend money on a premium cover and immediately put it through the same contact. This logic applies to mixed streams in a recycling conveyor system, where a change in feed can send hard pieces into a skirt that ran clean the day before.

05 When Does Another Millimetre Earn Its Cost?

I would not use a single wear percentage as the buying rule. A belt may be retired with a substantial amount of rubber left because one narrow score has reached the ply. Another can run until a broad area approaches an agreed replacement depth. The maintenance log ought to say which happened. Extra cover is worth discussing for the second case; for the first, I would want the side contact found and corrected before pricing another millimetre.

Extra rubber travels around the whole loop. On a long installation, the added mass belongs in the drive calculation. On a short conveyor it may be unremarkable. I would still ask for the proposed overall thickness and the maker’s pulley recommendation, because the carcass, covers and joint have to bend together. It is easy to overstate the cost of one millimetre; it is just as easy to ignore it on a belt that is already awkward around the tail.

A useful buying exercise is to put two candidates on the same drawing. Hold width, carcass and splice proposal constant if the goal is to isolate compound choice. If thickness changes, ask the supplier to show the new overall thickness, mass, minimum pulley guidance and joint method. If carcass changes too, you are evaluating a new belt construction, not a simple cover upgrade.

Old-belt observation A thickness change is worth examining when… First competing action
Even cover depletion over a broad area Service ends at a repeatable minimum depth Compare compound test results and operating wear trend
Isolated pits at a falling-material landing Fabric is approached locally despite sound support Reduce drop and check impact support
One score along a skirt The contact has been corrected and residual wear remains Remove the trapped-material route
Cracks appearing around a pulley The new complete build has adequate flex margin Verify diameter, tension and carcass suitability

06 Read a Compound Test Without Turning It Into a Warranty

Abrasion loss is commonly quoted as a volume under a named test method. Do not compare a number on one datasheet with an unlabeled “premium” claim on another. Request the method, the actual result, test piece information and the maker’s compound designation. Where the project uses a specified cover grade, write its standard and edition into the RFQ. A supplier can then explain what is supplied and which test evidence supports it.

I would hesitate to award the order to the lowest number on that sheet. The drum has a defined abrasive; the loading box may be receiving sharp rock, damp clay and a few pieces of steel. Wear at a cleaner may be fed by carryback that never touched the laboratory specimen. Where cuts dominate the retired belt, put the cut and tear data beside the abrasion result. Where the feed is hot or oily, ask which rubber compounds remain suitable after that exposure is taken into account.

Keep the performance comparison local. Put the retired belt’s cover and the candidate covers through the same test, where practical, and collect photographs and thickness readings from the same positions after installation. A short trend measured at several spots says more than a single dramatic photograph at change-out. The quality assurance discussion becomes concrete when the buyer supplies the positions, date and duty alongside every measurement.

07 Put the Old Belt Into the Enquiry

The enquiry should read a little like a maintenance note. “Largest lump normally 150 mm; occasional oversize larger; damage begins 400 mm after chute lip” tells the supplier more than a claim of heavy abrasion. Add belt speed and width, centre distance, trough angle and the old carcass designation. Photograph the first exposed fabric with a rule. Then include pulley diameters and joint type, because a heavier offer that will not wrap the tail is no offer at all. If the cleaner or skirt is involved, send a picture of its setting.

On the reply, I want both covers stated separately and the carcass written out in full. The compound code should match a test report with a named method; the total thickness, belt mass, pulley guidance and splice method belong on the same sheet. Ask the conveyor belt manufacturer to circle the old failure it expects its proposal to address. That answer can be checked after six months on the line.

The same form can serve several conveyors without putting the same belt on every one. A line with dry fines under a long skirt and a short loader taking broken rock have little in common at the top cover. Keep their wear records side by side, but leave room for separate specifications. With a conveyor belt supplier, I would check the compound and carcass codes on arrival against the signed quotation. Six months later, that small piece of paperwork will matter.

Send the old-belt photos and present specification for a comparison

08 Questions From the Buying Desk

Will a deeper top cover give us another year?

On a belt worn evenly by fines, the extra depth may delay the date when fabric becomes exposed. If the old belt has a single knife-like score at a skirt, I would find the cutting contact first. The replacement’s full construction still has to suit the pulleys and the intended joint.

What can we learn from the drum test result?

I can use it to rank two samples tested in the same manner. I cannot convert the difference directly into a date for the next belt change. ISO makes the limitation clear. Bring the old belt sample and the feed description into the discussion, then measure the replacement at the same marked places once it is running.

Can a better compound compensate for a thin cover?

It can reduce the rate of broad rubbing wear if it suits the material. It cannot provide missing penetration depth at a sharp, heavy impact. Check the transferred material, supporting structure and minimum remaining cover before choosing the thinner option.

Does this hollow come from fines or falling lumps?

On the worn belt I would draw the chute outline in chalk. A smooth dish extending under the skirts makes me look at the fines and skirt setting. Torn craters right under the landing point send me to the lump path. I have to be careful when the cuts sit inside a wider polished dish; the fines and the lumps are probably each doing damage. On a scrap sample I would cut through one crater and one smooth place, then compare how close each came to the ply.

Should we specify a stiffer carcass for impact?

Perhaps, if the existing belt dives between supports at the landing and the proposed build still fits the machine. The installed pulleys, tension and trough angle put limits on that choice. Before the order is signed, I would want the new ply layout drawn beside the actual tail diameter and the splice the crew intends to make.

What would you put in the enquiry email?

I would send two photographs of the retired belt: one close enough for the cut and one wide enough to locate it. The date when fabric first appeared is useful, if somebody recorded it. On the same sheet put the feed size and drop, belt speed and width, old build, installed pulleys and joint. The returned quote should name each cover, rubber code, test result and carcass, plus the overall mass, pulley check and splice. That is a document worth comparing line by line.

prev
Conveyor Belts for Power Plants: Coal, Biomass and the Dust Between
V-Belt Selection by Failure Mode, Not by Catalogue Section
next
recommended for you
Get in touch with us
QUICK LINKS
CONTACT US
Contacts: Leo Lei
Tel: 0086-18668582073
Address: Room 1602, sanlong building, tiangao street, south cbd, yinzhou district, ningbo, zhejiang ,china


We are focusing on material handling, power transmission and industry application.

Copyright © 2026 Ningbo Sinoconve Belt Co., Ltd. - www.scconveyorbelt.com | Sitemap | Privacy Policy
Contact us
email
whatsapp
Contact customer service
Contact us
email
whatsapp
cancel
Customer service