Empty run, no complaint. Feed the incline and the left wall begins to lean; by the head, fines have found the cleat end. The operator sees spillage, but the drawing may have missed a more basic fact: the loaded belt does not hold the section shown on paper. Stop the line and measure that section before ordering another cover grade.
Two measurements are worth keeping from that stop: wall spacing under load, and the bend that the base actually makes over the head supports. The catalogue drawing supplies neither.
Consider a pocket near the boot. Its floor is the base belt, its sides are corrugated walls, and the downhill face is a transverse cleat. There are separate bonds along all three boundaries. Which one is carrying the load when wet feed arrives in a slug? A cross-section of an old failed joint can answer more than a hardness certificate.
The chute can hold a wet plug and release it onto one cleat. Record that event before clearing the blockage. A bucket sample collected afterward will not show the impact. For T, C or TC, use the actual lump and drop location.
Follow one marked cleat through the head turn. It moves relative to the walls; the folds open and close; the base changes curvature at each contact. The first hairline crack may therefore turn up on the head side of a reinforcement edge, even though the loading chute seems the obvious suspect. Location alone is not proof—section the crack and inspect the roll faces.
Put a loaded pocket sketch beside the head arrangement. Check the cleat root, wall pitch and base construction on the same drawing, then compare the installed wheel diameters. Available forms appear on the sidewall conveyor belt page; the dimensions for this machine still need approval.
Share the loaded layout and head-wheel dimensions for a belt review
A gentle incline with free-running material may be served by an open ribbed belt. At a steep lift, the question changes: will an enclosed pocket arrive at the head full enough to make the capacity, and will it empty without dragging a second load around? Sketch the transfer and cleaning access before quoting the belt. The cheap option on paper can become an awkward machine to maintain.
An order marked 'TC' still leaves the foot and crown unspecified. Lay the section from the quote over a cut section of the failed belt. Where does the reinforcing insert stop? Is the foot wider, or merely the crown? Ask for those dimensions with the offer.
Imagine the chute dropping one large stone squarely on a cleat crown. Now replace the stone with a bank of fines pressing across the whole face. Neither load is represented by the pocket's nominal volume. The crown, the foot and the clearance at the wall ends all need to suit the load that actually arrives.
At the wall end of a used cleat, dark fines can leave a line in the rubber. The centre may have no damage. Photograph the gap before washing it out. At the head, bend a new sample and see whether that same opening reappears between wall and cleat.
| Profile or joint feature | What to check on the section drawing | Potential fit | Early sign to inspect |
|---|---|---|---|
| T-style cleat. | Root width, crown stiffness and bond area. | Smaller pockets with suitably free-flowing feed. | Root lift or downhill lean. |
| C-style cleat. | Curved face, root geometry and impact path. | Loads that arrive in uneven slugs. | Cracking at the shoulder or root. |
| TC or reinforced cleat. | Crown support and its effect on bending. | Deep pockets subject to substantial load. | Crown split or bond separation. |
| Cleat-to-wall joint. | Gap, sealing detail and permitted fold movement. | Fine or damp feed near the wall. | Fines trapped at the root. |
For the larger layout question, the steep incline selection guide covers the machine and its duty. Here the focus stays on what happens to the cleat root and sidewall as the loaded belt goes through the head. Put that head detail beside any product comparison.
The open face of a chevron conveyor belt gives damp fines fewer places to hide. Pocketed construction can lift feed that would roll back, provided its bonds and discharge are designed for the route. Compare test feed and speed; the quoted incline angle cannot settle the choice alone.
At the boot, sight along the walls while a pocket is filled. If the two edges move apart, the base is bowing across its width. The same carcass must still flex lengthwise through the discharge. This is the awkward pairing in a sidewall design: stiff across the pocket, workable around the wheel.
On the failed section, find the edge of the cross insert with a knife cut. Sketch where it lies beneath each wall. The quote should show the corresponding layer and the cover over it. If those sections differ, ask the supplier to approve the existing head bend again.
At the boot, measure the distance between walls with a pocket full. At the head, take a second photograph as the same cleat passes the wheel. Both should be part of acceptance. A rigid floor that holds its shape on the incline can still be difficult to bend at discharge.
| Base construction to identify | Loaded pocket check | Head curve check | Information to request |
|---|---|---|---|
| Fabric carcass with transverse insert. | Wall lean and cross-width sag. | Insert edge and bond through the bend. | Section drawing and approved minimum diameters. |
| Additional cross reinforcement. | Support of deeper or wider pockets. | Bending at every wheel and roll. | Layer location and adhesion data. |
| High transverse stiffness build. | Pocket shape at design feed rate. | Required wheel size and splice flexibility. | Complete route approval from supplier. |
| Plain fabric base proposed for conversion. | Whether it can hold the wall spacing. | Cover bond and bend suitability. | Engineered conversion evidence. |
A peel figure without the broken sample is incomplete. Keep a photograph of the tested root. Rubber left on both sides is different from an interface that opens cleanly; contamination, cure and sample geometry may also change the result. Agree on the method before comparing two quotations.
At a splice, the two walls have to rejoin in register. Check the first and last corrugation and the adjacent cleat, then jog that joint over the head. A misaligned pitch makes a regular bump that can look like a wheel fault. The longitudinal carcass joint and any cross reinforcement also need their own splice detail.
A head drawing may join the centres of five rolls with one elegant arc. The belt does not run along that pencil line. Photograph a slow jog and mark its contact with each roll. One unsupported jump can account for a periodic thump.
On the failed belt, measure the total build and locate the transverse insert by cutting a section. Then check the installed wheel, not a radius printed on a preliminary drawing. The supplier's bending limit should apply to this build, with its operating tension and temperature. Thickness alone cannot sign off the curve.
Cut through a fine line beside the cross insert. Is the rubber intact beneath it, or has the bond opened? Patch selection depends on that answer. Label the carrying face and direction of travel on the sample before it goes to the bench.
A bright stripe on a fold suggests contact. A split in its valley may be fatigue. A lifted wall root implicates the joint. Mark one damaged pleat with paint and jog it past each numbered roll; the meeting point narrows the search.
| Design detail | What it changes | Evidence of a problem | Action |
|---|---|---|---|
| Wheel diameter and actual belt build. | Bending strain in layers and wall roots. | Cracks near a reinforcement edge. | Verify supplier minimum and installed diameter. |
| Wrap and direction of bending. | Length and direction of repeated flexing. | Fold cracks or displaced joints. | Review complete belt path. |
| Roll centres and alignment. | Support between contacts. | Bridging, vibration or uneven wear. | Survey installed positions under tension. |
| Clearance at wall and roll ends. | Local rubbing or pinching. | Polished stripe on the same fold. | Correct clearance and contact geometry. |
One large wheel is straightforward if the head has room for it. Several rolls save space but must share the change of direction. Walk the proposed path with the belt drawing in hand: support gap, roll face, wall clearance, bearing access. There is no width threshold that makes a roll bank automatically better.
Take four dimensions from every roll in the bank: diameter, face width, centre position and clearance to the wall. Survey again after tensioning. A single roll with a bright track may be doing work intended for the whole bank; merely adding another roll somewhere nearby may leave that contact unchanged.
Keep a way to reach the highest bearings and clean the roll faces. Material build-up changes the effective diameter and can put one fold under extra pressure. The wall may still look straight on the incline while the damage grows at the head.
Paint one pleat and jog the line. At the incline it stays compact; at the head it opens. If the valley has a split, put a scale beside it and photograph the wheel contact. The nominal wall height cannot explain where that split began.
Wrap the proposed wall sample around a wheel matching the installation. Are all folds moving? If most stay closed, mark the few doing the work. Compare that movement with a second wall build before deciding on pitch or thickness.
A thick wall can survive the loading shovel yet crack in a valley. Cut both a damaged fold and a sound one. Look for a shiny rub patch on the nearby frame. A material certificate cannot tell us whether that metal touched the pleat.
A hold-down wheel leaves its signature in the rubber. Locate the stripe while jogging slowly. If it crosses pleat crests, measure face position and clearance before changing pressure. The wall root must not be forced sideways to make the belt run quietly.
A narrow wheel face can make a surprisingly hot track. Touch nothing while the line runs; use a safe temperature check at a stop. Are the neighboring wheels marked in the same place? Record the offset and measure alignment before touching the hold-down setting.
After a wheel change, use a fixed camera position at normal load. Compare the floor between supports and the wall junction with earlier photographs. Record wheel centres on the drawing, along with take-up position, before anyone moves the next one.
The arithmetic box on a capacity sheet is often larger than the material that makes the trip. A wet feed can bridge above an empty corner; a dry one may slump across the cleat on the incline. Check the fill at the boot and again halfway up, with the line at its stated throughput. Use that observed section in the capacity discussion.
Pitch is a trade-off visible at the head. Space the cleats far apart and the upper face of the load may creep downhill. Pack them close and the belt acquires more bonded roots, with less room to clear trapped lumps. Run the troublesome feed, then inspect what remains in a pocket after discharge.
Do not alter a cleat pitch simply to obtain a tidy whole-number relationship with the wall folds. The end joint has to be sound, the wall must still flex, and the splice must close in register. Request a drawing that shows all three, with the two pitches dimensioned.
| Feed behavior | Pitch and fill question | Where load concentrates | What to watch at discharge |
|---|---|---|---|
| Free-flowing granules. | Does the pocket retain the design fill on the incline? | Broad contact on the cleat. | Rollback and recirculation. |
| Damp, angular fines. | How does the pocket respond to slugs? | Root and wall junction. | Caked fines or a lifted bond. |
| Cohesive or clay-bearing feed. | Does bridging leave pockets partly empty? | Intermittent lump load. | Uneven emptying and carryback. |
| Large lumps. | Can the boot control impact before the cleat? | Local point load on crown and base. | Broken pieces lodged in the next pocket. |
Collect a feed sample and a discharge sample on the same shift. New fines may have been made at the boot, by pieces rolling within a pocket or at the head chute. Without that comparison, changing the cleat crown is guesswork. Note the rate and moisture beside each sample.
On a torn return belt, mark clean rubber at the newest part of the break and dirt in any older separation. Follow the damage back toward the first lifted edge. The wall may have torn only after the base had already opened beside an insert.
Stop, isolate and photograph. Begin at the same cleat every inspection and work toward the splice. A ruler beside a tiny crack makes the next photograph comparable. Include roll tracks and dirt inside a bond opening; cleaning before the photograph erases useful evidence.
With repeated head cracks, compare the installed roll centres to the approved drawing. Tape measurements and a cut fold come before a compound change. There is no defensible wheel limit in an anecdote from an unrelated machine.
Send a sketch of the head with wheel diameters and roll centres marked on it. Add the take-up position, the return path and a photograph of the feed chute. Alongside it, give the conveyor belt manufacturer bulk density, wettest condition, largest lump and required rate. Belt width alone is an incomplete enquiry.
Put both offers beside the same marked-up head drawing. One may list a TC cleat yet omit the foot width or the bend limit. Ask the conveyor belt factory for a section, pitch, bond detail and splice drawing. Close those blanks before comparing price.
Tag a spare with the approved drawing revision and the machine name. Ask the conveyor belt supplier how this wall should be stored. A group buying wholesale conveyor belts may combine orders, but its steep lifts still need separate pocket and head dimensions.
A plain industrial conveyor belt record may supply tension and cover history. The old EP rubber conveyor belt data does not certify wall adhesion. File the transmission belt and V-belt drive history under its own equipment number.
Give a stocking conveyor belt distributor the approved revision and machine tag. Under quality assurance, keep the sample sections and splice photographs. Before arranging site service, measure access at the head and space for cure equipment.
At a quarry boot, inspect where rock first lands; see the mining and quarrying applications. At a terminal, inspect deposits and salt exposure around the head; see port bulk handling. The industries overview helps locate the duty, while the installed route establishes the bend.
Check the drive conveyor pulley against the same carcass approval. At the loading boot, check whether the impact idlers or support bed hold the floor of the pocket level when material arrives. A robust cleat cannot fix a floor that collapses beneath it.
Request a cleat profile and deflection wheel review for your incline
Does the damp feed travel as grains or a single plug? Watch one discharge from the chute. Mark the impact point on the cleat section. A broad foot is worth considering if the joint and bend are approved for it; the profile letter alone does not answer the question.
Ask for the limit on this particular construction. Give the supplier the tension, temperature, bend direction and actual roll sequence. Then measure the hardware already installed. A simple thickness multiplier cannot account for the wall root and the transverse insert.
Cut the first lifted spot and note which layer separated. A convex turn cycles the wall and the base together, but a dirty bond, bad splice or rubbing roll can produce a similar location. Compare the section with the wheel dimensions and contact tracks before naming one cause.
A higher wall enlarges the pocket on paper. It may also leave an empty upper corner if the material bridges, or a spilling edge if feed is uneven. Check the filled cross-section on the running lift and whether the head empties it. That is the capacity the plant receives.
Place the cleat-end drawing over the wall corrugation drawing. Can the joint be made without trapping a moving fold, and will the splice line up? A convenient integer relationship between pitches is only one possible detail. The approved joint is the controlling one.
Section the flat belt first. Photograph its carcass, cover and splice, then trace every wheel in the proposed route. Only a designed and tested wall joint can answer whether this belt is a candidate for conversion.
Related Articles:
PRODUCTS

We are focusing on material handling, power transmission and industry application.