The stamping says SPZ 612. The stores request says “612 mm belt.” That small omission is where a replacement order can go astray. It is enough to start, but the letters and digits answer different questions. SPZ identifies the cross-section. In a standard metric wedge-belt listing, 612 is the datum length in millimetres, Ld. A tape around the back measures a different path.
Do not discard the belt whose marking started the enquiry. A phone photograph can preserve a fading code. At the machine, the groove and motor-slide position deserve the same attention as the belt label. The correct code cannot rescue a groove worn down to its bottom.
Narrow V-belts are sold in several profiles. This guide is for the buyer reading an existing drive, not for sizing a new one from motor power alone.
SPZ, SPA and SPB are metric narrow wedge sections. For the three sections, the table lists nominal widths and heights: 9.7 × 8, 12.7 × 10 and 16.3 × 13 mm. A flattened old belt may give a misleading caliper reading. Use the drawing for the pulley, if available. The groove profile and machine documentation carry more weight.
| Marking | Approximate top width × height | What the letters establish | What still needs checking |
|---|---|---|---|
| SPZ | 9.7 × 8 mm | Small metric narrow section | SPZ groove and minimum pulley diameter for the selected belt |
| SPA | 12.7 × 10 mm | Middle metric narrow section | SPA groove, number of grooves and drive duty |
| SPB | 16.3 × 13 mm | Larger metric narrow section | SPB groove, tension range and matching on multi-belt drives |
The profiles do not form a ladder of interchangeable sizes. An SPA is not a stronger SPZ that can simply be laid into the same sheave. It may go round the pulleys and still ride incorrectly. The pulley stamp or its groove drawing settles the question.
The photographs show A-section codes, from the classical family. They illustrate the marking format; their belts are not SPZ, SPA or SPB samples.
For a metric SPZ catalogue, the 612 in SPZ 612 is 612 mm of datum length, Ld. You may see “Ld” printed as well. Do not borrow that reading for a 3V label or an unfamiliar suffix; pull up the maker’s size table.
Datum length follows a defined reference line in the belt and measuring pulley system. Outside length, La, follows the back of the belt; inside length, Li, follows the inner path. They are different values for the same belt. A tape laid around a used belt may also reflect wear and permanent set. Never convert a measured outside loop directly into “SPZ” plus the same digits.
| Example on an order | Read it as | Do not assume |
|---|---|---|
| SPZ 612 | SPZ profile, 612 mm datum length where the metric Ld convention is used | 612 mm measured around the belt back |
| SPA 1250 Ld | SPA profile, 1250 mm datum length explicitly marked | The same outside length as a belt marked 1250 La |
| 3V or 5V followed by digits | A different narrow-belt designation system | Direct numerical equivalence with SPZ or SPB |
Some maker charts identify certain SPZ and 3V, or SPB and 5V sizes as replaceable. That is a charted cross-reference, not permission to mix profiles or length conventions by eye. It also does not mean that belts from the two systems belong together in one matched set.
Take the guard off under the plant's isolation procedure and inspect the groove. The side faces do the driving. Polish at the groove bottom is a reason to stop and check whether the belt has sunk into a worn sheave. An uneven lip calls for a groove inspection too. Otherwise the new set can acquire the old set’s glaze.
A narrow section can transmit power in a compact drive, but pulley diameter and belt construction still set limits. A small sheave might still be below the chosen belt’s limit. Check the product sheet and the drive calculation whenever a motor or pulley has been altered. The classical V-belt range has its own profiles; a conversion involves new groove geometry and ratings.
On a multi-groove drive, one new belt beside several worn ones is a poor experiment. The old loops have had different lives, even if they began as a set. Ask whether the new shipment is matched or supplied under a set-tolerance system. Fit the complete group, keeping section, nominal length and construction identical; use the specified tensioning procedure.
Do not diagnose every hot set as a matching problem. Heat may start at a bearing, offset pulley or altered machine load. A photograph of the failed belt’s flanks and underside belongs with the order; so do the alignment and groove checks. Follow the specified run-in inspection and tension schedule.
A longer belt with the same prefix is a different part number. It may fit because the motor slide has travel, yet a changed centre distance can change take-up reserve and wrap. A moved motor changes the geometry. Put its new position on the drive sketch, and never mix the longer loop with the original members.
Start with the parts list and pulley markings. No readable marks? Draw the motor slide as found, with both ends of its usable travel. Mark the measured centre distance, groove count and sheave sizes on that drawing. Measure the old belt too, but label that measurement “used belt.” The old loop is evidence, not a final order code. A photograph with a scale beside the belt and another square-on view of the clean pulley groove lets the supplier see what the text cannot.
| What you find | Next check | Ordering consequence |
|---|---|---|
| Legible SPZ, SPA or SPB code | Compare with parts book and groove marking | Quote full profile and datum length |
| No code, pulley marking survives | Check groove condition and drive geometry | Confirm length from a maker's sizing method |
| Belt sits low and contacts the groove bottom | Check groove wear and section | Do not order by the old belt alone |
| Only one belt of a set is broken | Check alignment, load and condition of all grooves | Order a complete matched set if that drive uses one |
| Flank glazed on one side | Check pulley offset, parallelism and tension | Correct the drive fault with the replacement |
XPZ, XPA and XPB identify notched narrow profiles in many catalogues. The notches on its inner face help it flex, particularly on a compact drive. An XPZ still needs the right groove, and notches will not restore worn metal. Compare the maker’s ratings and pulley limit before ordering a cogged V-belt in place of a wrapped version.
Double V-belts are designed for appropriate drives with working faces on both sides. A timing belt uses tooth engagement when shaft timing matters. Neither is a routine replacement for a single-sided SP belt. Other specialist ranges, including PU V-belts and agricultural V-belts, likewise need their own pulley and duty checks.
An enquiry can begin with one unedited photograph of the stamping. Type the code beneath it, suffix included, and say whether the quantity is pieces or complete sets. Add the machine model, sheave photos and a note about oil, dust or heat. A new machine needs a drive calculation: input power and speed, output speed, sheave diameters and adjustment range belong on the drawing.
SINOCONVE’s manufactured transmission-belt range includes these profiles. Its V-belt range and manufacturer information provide product context. Send the marking and drive details through the contact page for a section and length review.
No. In a standard metric SPZ listing, 612 mm is the datum length, Ld. Outside and inside lengths are different references. The catalogue should settle any suffix or alternate length convention.
Not as a direct swap. The belt profiles and corresponding grooves differ. A drive redesign may use another section, but it requires pulley and power-rating checks.
They are separate designation systems. Find the exact pair in a maker’s cross-reference chart and compare the groove and length basis. Keep each multi-belt set within one specified profile and construction.
A fresh belt beside stretched, worn neighbours may do disproportionate work. Order the set under the supplier’s matching method. Then inspect the sheaves and alignment that damaged the first set.
A photograph of the parts book, clean pulley grooves and motor slide is a useful start. Put a ruler in one frame. An outside tape measurement of the old belt is only a clue, not a reliable substitute for the specified datum length.
Notches can ease flexing, but a hot bearing or worn groove remains hot. Compare the wrapped and cogged product ratings for this pulley before changing the construction.
Related Articles:
PRODUCTS

We are focusing on material handling, power transmission and industry application.